How-To Tuesdays
shell&thread_necklace_30.jpg
One of my dearest friends, Nik Schulz, is a creative illustrator. This weekend he brought me a valentine that is exactly what I wanted: a DIY project to share with you! Nik lived for half a year on St. Agnes, a tiny island in the Isles of Scilly. And while he was there, he sailed, learned knot tying, and collected some unique seashells. Thus, the Knotted Seashell Necklace came to be. The knots are very clever and the overlapping lends a woven look to the final result. This is a great project for the beginning knot maker, and to help you along, I took a short video of Nik explaining the method he uses for threading the shells. I love the necklace so much, but I loved watching him make it even more. Thanks Nik!


shell&thread_necklace_01.jpg

Materials

Seashells
Thin, waxed linen cord
Drill with 1/16″ bit
2×4 with 2 nails, 12″ apart
Scissors
Clasp

Directions

shell&thread_necklace_02.jpg
Step 1: Chose 7 seashells for the necklace. I chose a center piece first and then selected 6 other shells that played off the colors and patterns in it.
shell&thread_necklace_03.jpg
Step 2: Drill a small hole in each shell. Drill from the inside of the shell to the outside. It is most important to use light pressure so as not to crack the shell. Practice a few times to make sure you have your method down.
shell&thread_necklace_04.jpg
Step 3: Cut 7 cords, each 1′ long.
Thread the Shells:

shell&thread_necklace_05.jpg
Step 4: Slide one shell onto a piece of cord. The half of the thread coming out of the top of the shell shall be called the top thread. The half of the cord coming out of the bottom of the shell will be called the lower thread. Push the shell down the thread so that the top thread is 3″ longer than the lower thread.
shell&thread_necklace_06.jpg
Step 5: Lock the lower thread against the shell with your thumb, and with your free hand, form a 3/4″ U-shaped loop with the top thread. This is called a bight.
shell&thread_necklace_08.jpg
Step 6: Wrap the top thread around the bottom of bight and the lower thread.
shell&thread_necklace_09.jpg
Step 7: Keep wrapping until 5 wraps have been formed. Use your nails in between to push the wraps tightly together.
shell&thread_necklace_11.jpg
Step 8: On the 6th and final wrap, pass the top thread through the loop, being sure to capture the lower thread in the process.
shell&thread_necklace_12.jpg
shell&thread_necklace_13.jpg
Step 9: Grab the wraps and slide them all away from the seashell to close the loop. Pull only on the thread, if you put pressure on the shell, it could break.
shell&thread_necklace_14.jpg
shell&thread_necklace_15.jpg
shell&thread_necklace_16.jpg
Step 10: Pull the lower thread and slide the wraps back down towards the shell to close the loop holding the shell. Repeat Steps 4 through 10 with the remaining shells.
String the Necklace:
shell&thread_necklace_17.jpg
Step 11: Cut 32″ of cord. Center it onto the 2 nails, and secure the ends to the nails.
shell&thread_necklace_18.jpg
Step 12: Start with the center shell. Hold it against the back of the thread and center it. Form a "V" with the 2 threads that hangs about 5/8″.
shell&thread_necklace_20.jpg
shell&thread_necklace_21.jpg
Step 13: Tie each end of the "V" to the necklace using a simple clove hitch. Don't tighten them down too tight yet, so that they can be adjusted if needed later.
shell&thread_necklace_22.jpg
shell&thread_necklace_24.jpg
Step 14: Repeat the process with the remaining shells, being sure to overlap the "V" of each shell. It will get crowded along the necklace, but work slowly and deliberately.
shell&thread_necklace_27.jpg
Step 15: Add the clasp using the same wrap knots that you tied for the shells. When positioning the clasps for length, take into account that when you close the loop for the clasp, the necklace will get a bit longer.
shell&thread_necklace_30.jpg
Step 16: Put it on a pretty girl, and then trim the cords to taste! I like mine wild!

Tagged Craft Projects Crafting with Nature fashion jewelry knots necklace